News
» Go to news mainRobotic Boat to Sail Across the Atlantic
Sailing their way intoĀ the Guinness Book of World Records could be a challenge, but itās certainly the goal for an engineering group at Dal. The team has custom built an autonomous, robotic sailboat capable of piloting itself from the coast of Nova Scotia to Europe.
Piotr Kawalec and Graham Muirhead are hoping to launch the teamās 2-meter vessel this spring as part of the Microtransat Challenge: A difficult race that many universities have attempted to accomplish, but failed to finish.Ā
With help from a group of students and faculty from Dalās departments of Electrical and Mechanical Engineering, itās taken approximately 5 months to build the sailboat. The team includes professors Rob Warner and J.F. Bousquet, students Andrew Dobbin, Thomas Gwynne-Timothy, Julia Sarty, and George Shannon, and other staff members.
The goal is to have the small sailboat leave the waters off the shores of the Halifax Harbour and travel across more than 3,500 kilometers of Atlantic Ocean to France.
As per the rules of the challenge, the vessel cannot exceed 4 meters in length and can use only wind power to make its sixty-day long journey.Ā
Kawalec says that even though the Microtransat Challenge has been around for ten years, no one has ever designed an autonomous boat of this scale capable of sailing across the Atlantic Ocean. Ā
āI think there are autonomous vessels out there that can sail across, but when you have a large boat to work with you can pack a lot more batteries and gear inside,ā says Kawalec. āThe challenge is that with something really small, the waves just toss it around. So far, no one has even got to the official start line.ā
The start line is 200 kilometers off the shore of Newfoundland, with the finish line about 200 kilometers off the western shore of Europe along the French coast.Ā Ā Ā
Disaster at seaĀ
This isn't the first time Dal's Faculty of Engineering has competed in the Microtransat Challenge.
Their first attempt was in 2015 in partnership with Ensta Bretagne, a naval architecture school in France, The school supplied Dalās team with the vessel that was used in the challenge. From there, the team equipped the vessel with appropriate controls necessary to make its sail across the ocean. Unfortunately, failure occurred about 500 kilometers into the boatās journey.
āOn our first attempt we lost it somewhere near Sable Island and never recovered it,ā says Kawalec. āWe had GPS tracking on the vessel and could see that it had started going around in circles. It just drifted around Sable Island for a couple of weeks and then we lost communication.ā
Kawalec and Muirhead say the boat either sank or the batteries eventually died; A common occurrence for these types of small vessels that take part in the challenge.
āThe Microtransat website hosts a tracking map of all the boats that are launched, so you can see that they all start off fairly well and then start to loop in circles,ā says Muirhead. āSeems to be the normal pattern.ā
This year, Muirhead and Kawalec are hoping to break tradition and set sail on a new path.Ā The first step was building their sailboat from scratch.
Creating a new designĀ
"I didn't work too much on the first boat, but it was provided to us by a naval architecture school. It was already made so we were constrained by what we had to work with,ā says Kawalec. āWhen youāre building something like this, you want to line up your electrical systems with your mechanical systems. So, after the first year we decided that if we were going to do this again, we should build it the way we wanted.ā
To start, the team spent a great amount of time considering all possible scenarios their boat could face on the Atlantic. This included how much battery power the boat required and what would happen if the vessel took on water.
āWe canāt predict what weāre going to hit out there because itās open ocean, but anything we could think of to implement that was feasible for us, we did, which was key for this boat,ā says Kawalec.
The number one issue was the durability of the boatās hull. The vessel used in the 2015 Microtransat Challenge had a hull that had been built of foam with a thin skin. The new sailboat however, is made out of Carbon Kevlar composite laminate.
āYou can probably hit it with a hammer and it would be fine,ā says Muirhead. āMaking a strong boat was one of the biggest prioritiesā.
Muirhead says the other problem with the design of the 2015 vessel was that it had a fin keel; a long narrowĀ plateĀ that projectsĀ fromĀ theĀ bottom of a vesselĀ toĀ giveĀ itĀ greater lateralĀ stability.
āThe weight that keeps it upright was a long way down and it was catching quite a few weeds,ā says Muirhead. āSo we wanted to go with a full keel design thatās a little smoother along the water.ā
The next step was trying to ensure that the boat was waterproof. To achieve that, the new hull has been built with a tightly secured lid that will prevent water from penetration. Though, Kawalec says if that should happen, all the electronic components inside the vessel have been individually waterproofed as well.
Should that fail, there is a plan B.
āBefore we launch the vessel, weāre going to fill it with ping pong balls so if there was a breach and the vessel was to flood, it would still stay afloat,ā says Kawalec. āThe boat wonāt perform as well because itāll be heavier but it should still be capable of moving.ā
Finally, communication with the boat itself was a key concern.
āThe first boat had a GPS that could send its coordinates so we could track it, but we had no way of getting any other data out of it,ā says Kawalec.
āAnd that was one of the biggest problems with the first boat,ā adds Muirhead. Ā āWhen the boat failed we didnāt really know why. We saw where it was, but that was all. To know more would have been very useful.
This year the team has implemented a satellite-based communication system that will provide them with data on the boatās current condition.Ā
āWeāre hoping to do some monitoring as far as battery consumption, and we have sensors inside that can tell us if there is a hull breach or water taken on,ā says Kawalec. āThe vessel can also send back wind speed and other conditions. This way we can better understand what the boat is going through so that we can improve for next time.ā
The sailboat also has a GPS tracking device that was provided to the team by Xeos Technologies, a local company in Halifax.
āTheyāre giving us two GPS trackers and theyāre maintaining them for us,ā says Kawalec. āItās a big help and something we wouldnāt be able to do on our own.ā
Although weather conditions are the number one hazard for the attempt, there are other dangers to consider.
āMarine traffic is the second biggest danger for this boat,ā says Kawalec. āHigh seas can toss it around but if it slams into a container ship, that could be a game changer for us.ā
Another game changer; if someone picks up the boat on the open water.
āThatās partly why the boat says āDonāt touchā and we have Piotrās contact number on the back,ā says Muirhead.Ā āIf you see this, just tell us where it is, please donāt take it home with you.āĀ Ā Ā
They certainly did, but Kyle says it wasnāt easy.
Testing and launchĀ
The team is still in the process of working out the final touches to their robotic sailboat, but hope to launch the vesset this April or May.
The team did have the opportunity to test their vessel last September, taking it out a few times in light and moderate wind conditions and watching as the sailboat bobbed up and down in the Halifax Harbor.
āThereās always this question of what conditions we should expect on the ocean and should there be changes in programming if there is a storm event,ā says Muirhead.Ā āWe did enough testing in winds up to 20 knots, and the boat did pretty good in those waves.ā
Muirhead says from now till spring, heāll keep an eye on predicted weather conditions before deciding when to launch the boat. Although he and Kawalec are certainly hoping that their boat reaches the finish line, they admit that Europe is a long way from Halifax.
āWeāre at the stage where weāre just trying to make gains on the previous attempt. Thatās our big focus. How can we make this better than the last one?ā says Muirhead
āThe Dean did promise that if the sailboats makes it to Europe, weāre getting a trip to France to recover the boat,ā adds Kawalec. āI think if it did make it across that would probably qualify for a Guinness World Record.ā Ā Ā
Recent News
- Dalhousie Professors Recognized with Prestigious CSME Medals
- USRA Grant Sparks New Paths in Renewable Energy for Dal Engineering Students
- A New Chapter in Design Engineering
- Dr. Paul Amyotte, P.Eng. Honoured as Discovery Centre Hall of Fame Award Winner
- Jon Tottenās Unexpected Journey to Teaching Excellence
- Dal Solutions: Breakthrough poised to transform wastewater treatment worldwide
- Grad Profile: A Revolutionizing Journey in Additive Manufacturing
- A Solar Journey: Jessica Durhamās First Year at pilipiliĀž» Engineering